Saubier.com

Saubier.com (http://www.saubier.com/forum/index.php)
-   Small Caliber Discussion Board (http://www.saubier.com/forum/forumdisplay.php?f=2)
-   -   Devcon 10110 for Bedding Rifles (http://www.saubier.com/forum/showthread.php?t=13829)

Dean2 04-19-2011 05:07 PM

Devcon 10110 for Bedding Rifles
 
Starting last year I ran out of and could no longer get my favourite bedding compound "Micro-Bed". I tried a nubmer of others over the years and never was entirely satisfied. After reading so many good things about Devcon, decided to try it. Took some learning time, and it behaves WAY different than the any of the compounds I previously used.

What I learned;
Kiwi clear shoe polish is the best release agent. Per all the website postings, tried Pam, wood floor wax, auto wax, carnuba car wax and release agent. Top two are Kiwi and Carnuba based was, whether floor or auto.

You must get the mix ratios very close. If you have the gear to do it by weight 9:1, this is far superior to trying to judge the 2.5:1 volume.

Make sure you fill any voids that will cause mechanical locking with plastercine and make sure you wax ALL metal on hte gun, including the bottom metal and action screws, and any part of the wood exterior where you don't want it to stick. Once this stuff is hard, it is strong as hell, does not compress and is hard to fracture.

If you get a tight lock that won't release with a pop on the barrel with a rubber mallet, put the whole thing in the freezer for about three hours. This will make popping it loose muuch easier.

Overflow, clean up large bits with a popsicle stick. The residue cleans up real well with Hoppes #9 on a cloth patch or piece of paper towel. It iwll also clean it off your hands well.

To get a perfecT, void free job, you should leave the gun set up for 24 or better yet 30 hours. It will actually pop out much easier and cleaner than if you try to take it out early, as long as you have no mechanical locks or parts you forget to put polish on.

I would be interested in any tips ohers have for using Devcon.

ab_bentley 04-19-2011 05:22 PM

Take you shoe polish and set it the stove burner on low (electric). It will melt the entire thing and make application much easier. It will also fill in small voids that the plumbers putty missed. Also instead of popsicle sticks use Q-tips with the heads soaked in Butches or Hoppe's. Also remove the action screws before the reicever (unscrew them) it will prevent machanical lock. Adam

turbineman 04-19-2011 07:34 PM

We use it in the power generating field, the stuff is unbelievably strong and can be machined if need be. we mainly use the ceramic, stainless and aluminum epoxy. this is the best stuff out there for our applications, let it cure at about 80 to 90 deg. for at least 24 hrs up to 36 hrs if you can, and your good to go! this stuff is expensive but more than worth it.

Dean2 04-20-2011 01:17 AM

Adam

Some good points. Especially the ones about cracking the screws loose after about 4 hours. I actually crack them then retighten them. I do that no matter what compound I am bedding with cause I learned once the hard way just how tight they can get. Good thing that one had Allen head screws, slots would have never released.

steve b. 04-20-2011 01:19 AM

I have used Devcon on a few rifles and thought it was ok. i switched to Pro Bed 2000 and have never looked back. 40 some stocks later.

Daryl 04-20-2011 02:50 PM

I hate using odd-mix ratios.

For years I used Devcon 50/50 steel impregnated epoxy & loved it for bedding - is it still available?

SShooterZ 04-20-2011 04:22 PM

Is it this stuff?

http://www.midwayusa.com/viewProduct...tNumber=647161

I plan on trying some myself soon.

Dean2 04-21-2011 12:15 PM

SShootrz

The stuff from Midway is a good price for Devcon, depending on what they charge for shipping, I buy mine from MSC Induxtrial, it is $41 a tub but they will ship two tubs to Canada for $13, and that more than offsets the extra $12 for me.

The one you have pictured is the standard Devcon steel 10110. It has the 2.5:1 by volume mix ratio. I do not believe Devcon makes the 50:50 steel putty any more but I have never used anyhting but 10110, so some of their other mixes may be 50:50.

john 04-23-2011 02:52 AM

devcon
 
Devcon 1:1 mix is still available in NZ, at least; as a blister pack with two tubes or as tins. Its been the same offering for at least the last 40 years.

Stephen Perry 04-23-2011 01:43 PM

Devcon, JB, and AcraGlas Work Fine
 
Have done bedding and glue-ins with all three. My item to add when glueing in use the barreled action not just the action this need to be checked for alignment sometimes more fitting is needed. Set-up using sandbags to support the stock both sides and back, under forend and on top of action while supporting under the barrel and on top of barrel. I like glue and screw/pillar bed when pillar bedding is not used by itself. Devcon is fine but somewhat stringy. JB I prefer, smooth application allows more working time than Devcon before things start to set up. Fill the voids with wax most any silicone based release agent works fine. Brownell products are top notch here. Wood/Fiberglass scrappers do a good job on the excess.

First time glueing-in have no fear. Use your common sense to guide you along with advice and reading-up has provided you. As far as leave time for set up, week will do it - some go a day. Scrape off excess in the beginning but leave the bedding compound/glue-in material alone to do the job your seeking. Taking care of your action/stock bedding is one of those items in gun maintenace you can do yourself with a minimum of specialized tools. You can also bed your shotgun and pistol stocks with similar techniques.

Stephen Perry
Angeles BR


All times are GMT. The time now is 01:38 PM.

Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.