Forum: Classifieds
02-20-2024, 01:30 AM
|
Replies: 15
Views: 1,714
No disrespect George, but you didn't understand...
No disrespect George, but you didn't understand my response. In no way did I say the that .7gr was an acceptable error in a small case. What I did say is that the scale could be off by a percentage...
|
Forum: Classifieds
02-11-2024, 12:56 AM
|
Replies: 15
Views: 1,714
I see I misunderstood the OPs original post, so...
I see I misunderstood the OPs original post, so my previous post isn't relevant to the question.
I see the recommendations to clean the balance scale. I agree. My old RCBS scale was acting funny a...
|
Forum: Classifieds
02-08-2024, 12:59 AM
|
Replies: 15
Views: 1,714
Usually, the scale might have a range of...
Usually, the scale might have a range of acceptable deviation. In your case .7 gr off at 154 gr is only about 1/2 of a percent, which isn't bad really. If I were you, I would verify that the...
|
Forum: Small Caliber Load Data
02-08-2024, 12:42 AM
|
Replies: 12
Views: 1,742
|
Forum: Classifieds
12-12-2023, 01:41 AM
|
Replies: 12
Views: 2,586
|
Forum: Small Caliber Discussion Board
12-03-2023, 02:34 PM
|
Replies: 7
Views: 4,043
|
Forum: Bullet Making
02-13-2023, 12:38 AM
|
Replies: 4
Views: 35,627
|
Forum: Bullet Making
01-21-2023, 03:03 PM
|
Replies: 4
Views: 35,627
|
Forum: Small Caliber Discussion Board
05-30-2021, 02:20 AM
|
Replies: 5
Views: 2,945
|
Forum: Bullet Making
01-20-2021, 11:17 PM
|
Replies: 11
Views: 219,036
|
Forum: Small Caliber Discussion Board
12-29-2020, 03:40 AM
|
Replies: 17
Views: 6,505
|
Forum: Small Caliber Discussion Board
12-28-2020, 03:17 AM
|
Replies: 17
Views: 6,505
|
Forum: Small Caliber Discussion Board
12-03-2020, 12:25 AM
|
Replies: 27
Views: 9,312
Totally agree with you on that Bill. In that...
Totally agree with you on that Bill. In that case, I don't think it would matter what they had with them though, including a rifle of any caliber. I tend to think those on this forum could probably...
|
Forum: Small Caliber Discussion Board
12-01-2020, 12:19 AM
|
Replies: 27
Views: 9,312
|
Forum: Bullet Making
11-11-2020, 10:57 PM
|
Replies: 11
Views: 219,036
I have never used it so I can't say from...
I have never used it so I can't say from experience. I've found that if I clean the cores well and remove all the lubricant from the squirting operation they stick fine. I usually just wash them in...
|
Forum: Bullet Making
11-11-2020, 02:00 AM
|
Replies: 11
Views: 219,036
|
Forum: Small Caliber Discussion Board
10-25-2020, 12:25 AM
|
Replies: 7
Views: 3,984
If you just installed it and you have a lot of...
If you just installed it and you have a lot of data stored, it could take quite a while for the initial scan since it is scanning everything. Subsequent scans usually only scan anything new or things...
|
Forum: Small Caliber Discussion Board
10-06-2020, 02:49 AM
|
Replies: 32
Views: 11,192
|
Forum: Small Caliber Discussion Board
10-04-2020, 01:07 AM
|
Replies: 5
Views: 2,916
|
Forum: Small Caliber Load Data
10-04-2020, 01:04 AM
|
Replies: 8
Views: 13,494
|
Forum: Small Caliber Load Data
08-05-2020, 02:30 AM
|
Replies: 18
Views: 9,771
How much neck tension does your brass have? If...
How much neck tension does your brass have? If you have to press very hard to seat a bullet any brand die could cause a ring. You may also want to just polish the spot where the ring is in the...
|
Forum: Classifieds
04-07-2020, 03:56 AM
|
Replies: 6
Views: 3,813
|
Forum: Classifieds
04-06-2020, 03:04 AM
|
Replies: 6
Views: 3,813
|
Forum: Bullet Making
03-15-2020, 06:34 PM
|
Replies: 11
Views: 287,143
|
Forum: Small Caliber Discussion Board
03-08-2020, 07:02 PM
|
Replies: 13
Views: 6,608
|