Forum: Small Caliber Discussion Board
01-29-2021, 12:32 AM
|
Replies: 8
Views: 3,152
|
Forum: Classifieds
12-10-2020, 01:05 AM
|
Replies: 11
Views: 4,378
30 Herrett T/C barrel
Awesome, thank you.
Was cleaning out a few old boxes and ran across some brass and a few loaded rounds from my old barrel.
|
Forum: Classifieds
12-08-2020, 07:36 PM
|
Replies: 11
Views: 4,378
30 Herrett T/C barrel
Gary,
I tried to PM you but your inbox is full.
Do you have a Super-14 30 Herrett that you want to get rid of?
Dies too?
Got rid of mine a long time ago and have regretted it.
You can...
|
Forum: Small Caliber Discussion Board
04-28-2020, 09:21 PM
|
Replies: 8
Views: 3,191
|
Forum: Small Caliber Discussion Board
04-28-2020, 09:20 PM
|
Replies: 8
Views: 3,191
The two 17 Remingtons
I've owned have both been BDL, without sights and each barrel has two small S over top of each other at the end of the caliber marking.
|
Forum: Small Caliber Discussion Board
01-24-2020, 11:24 PM
|
Replies: 10
Views: 5,539
Check this company out
https://www.hoplitearms.com/
Similar concept, taken to a whole nuther level.
Theis and crew are very transparent about the rifles and the ammunition.
To use a worn out term, it really is...
|
Forum: Small Caliber Discussion Board
07-22-2019, 09:16 PM
|
Replies: 9
Views: 4,763
|
Forum: Small Caliber Discussion Board
07-20-2019, 11:45 AM
|
Replies: 9
Views: 4,763
|
Forum: Small Caliber Discussion Board
07-13-2019, 12:14 AM
|
Replies: 9
Views: 4,763
|
Forum: Small Caliber Load Data
12-25-2018, 12:41 PM
|
Replies: 21
Views: 11,756
|
Forum: Small Caliber Load Data
12-25-2018, 02:25 AM
|
Replies: 21
Views: 11,756
As soon as I saw the pic of the backed out...
As soon as I saw the pic of the backed out primer, I knew it was a headspace issue.
Measure the headspace of one of your unfired cases and one that you've fired. There will be a difference and the...
|
Forum: Classifieds
12-19-2018, 08:30 PM
|
Replies: 14
Views: 7,747
|
Forum: Small Caliber Load Data
03-22-2018, 08:12 PM
|
Replies: 7
Views: 4,809
|
Forum: Small Caliber Discussion Board
03-15-2018, 11:05 PM
|
Replies: 25
Views: 8,430
|
Forum: Small Caliber Discussion Board
02-10-2018, 03:02 PM
|
Replies: 16
Views: 6,868
|
Forum: Small Caliber Discussion Board
02-10-2018, 02:58 PM
|
Replies: 2
Views: 2,676
Thanks for the info Bill.
I already have a...
Thanks for the info Bill.
I already have a Cooper 21 in Mach IV
so doing that or the 17 Fireball doesn't really matter as much.
I also have a fluted SS Remington 17 Fireball barrel lying around...
|
Forum: Small Caliber Discussion Board
02-08-2018, 10:28 PM
|
Replies: 2
Views: 2,676
Need to rebarrel a CZ-527 from 221 FB to VarTarg
My dad's 221 got wet and was put away with moisture in the barrel.
It's jacked on the inside yet it still shoots well. Problem is the accuracy is only good for 30 or so shots.
I'd like to have...
|
Forum: Small Caliber Load Data
02-24-2017, 11:01 AM
|
Replies: 15
Views: 7,746
|
Forum: Small Caliber Discussion Board
02-06-2017, 11:09 PM
|
Replies: 55
Views: 36,216
|
Forum: Small Caliber Discussion Board
01-24-2017, 05:58 PM
|
Replies: 30
Views: 10,328
It could be worse
Sometimes here in Florida we wake up with the heat on and by 1pm we have to switch to the a/c.
Of course it's nothing like the winters out in your neck of the woods.
I lived in Mountain Home, ID...
|
Forum: Small Caliber Discussion Board
01-23-2017, 05:57 PM
|
Replies: 26
Views: 11,553
|
Forum: Small Caliber Discussion Board
01-20-2017, 11:06 AM
|
Replies: 31
Views: 7,402
Cartridgrs6
Ben,
The PPC family cannot be safely done in the contender. Too much pressure.
To answer what is the largest cartridge available, I have one in 45-70...
|
Forum: Small Caliber Discussion Board
01-16-2017, 10:05 PM
|
Replies: 12
Views: 6,315
|
Forum: Small Caliber Discussion Board
12-28-2016, 06:05 PM
|
Replies: 14
Views: 5,152
New site host suggestion
Gary Reeder of reeder custom guns dot com or net, not sure.
Just got a new host for his site. They used go daddy and the site still looks and operates the same.
His site had been hacked and they...
|
Forum: Small Caliber Discussion Board
12-04-2016, 11:22 PM
|
Replies: 18
Views: 6,973
How I set up my dies
I set any new die up by first loosening the decapping or seating stem. The die lock ring is also set up not making contact with the press and the set screw loosened.
For the sizing die, screw it...
|