Forum: Small Caliber Discussion Board
05-04-2009, 12:19 AM
|
Replies: 2
Views: 2,436
20br
I have 20 BR but I have not tried any 2015 in I have use it in a 223, I think it may be a bit to fast for the 20BR but if you do start out real low on the charge! I use VV 135 30.7-8 with Sierra...
|
Forum: Small Caliber Discussion Board
11-28-2008, 10:17 PM
|
Replies: 9
Views: 4,788
Seating die
Al, thats what I use. My 22BR seating die is a Redding and it works fine!
I also use my Redding 22BR for the neck sizing.
Here is the Redding number I use 607-753-3331
Jack
|
Forum: Small Caliber Discussion Board
11-28-2008, 10:11 PM
|
Replies: 9
Views: 4,788
Seating die
Al, thats what I use. My 22BR seating die is a Redding and it works fine!
Here is the Redding number I use 607-753-3331
Jack
|
Forum: Project Guns
10-03-2008, 02:52 PM
|
Replies: 29
Views: 19,961
20 cal. project
219DW and I went to the gunsmith yesterday with the new barrel, reamer and Rifle. Like he said (Dave) came up with spec's for the reamer!
I know Dave will have the new one shootin good!
Hope the...
|
Forum: Small Caliber Discussion Board
07-16-2008, 08:47 PM
|
Replies: 11
Views: 6,823
Hey! I have only used 2 powders for my 20BR. ...
Hey! I have only used 2 powders for my 20BR.
1st was N135 30.8grs. shot a .241 group, 2nd was with N140 32.2grs.
Forgot the 1st was with 39gr. Sierra BK , and 2nd was also with 39gr. Sierra's...
|
Forum: Small Caliber Discussion Board
06-23-2008, 01:20 AM
|
Replies: 3
Views: 4,295
20BR sizing
Need to say howdee!
I have a 20BR and this what I do: I use a 22BR full length sizing die without the expander. It takes it down to .240, then I use a neck sizing die (22BR) with a .237 bushing,...
|
Forum: Small Caliber Discussion Board
06-10-2008, 01:49 PM
|
Replies: 6
Views: 3,906
20BR forming
Here is what I do: 1st I use a Redding 22Br full length die, this brings it down to .240, Forgot! This without the expander! Next I use a Redding bushing die with a .237 bushing, next I use the...
|
Forum: Small Caliber Load Data
06-03-2008, 12:46 PM
|
Replies: 7
Views: 10,635
Thanks to:
I owe alot of thanks to Alberta Al He got me started with thw 20BR case forming information. Thanks to Al and everyone. Jack
|
Forum: Small Caliber Load Data
06-02-2008, 12:17 PM
|
Replies: 7
Views: 10,635
20BR Loading info
I will assume you have your case forming down pat!
I use only use V V N135 powder, I started off with 31grs. and got a crono reading of 4127fps. with a 39gr. sierra an thought, "hmm", that seems a...
|
Forum: Small Caliber Discussion Board
04-08-2008, 09:55 PM
|
Replies: 3
Views: 3,308
Case length
Hey I just got my 20BR back in NOV. The reamer that was used was PTG and the over-all length was 1.535 You need to call the people that are installing the barrel to see what reamer they are using,...
|
Forum: Small Caliber Discussion Board
02-19-2008, 11:40 PM
|
Replies: 28
Views: 11,514
|
Forum: Small Caliber Discussion Board
01-25-2008, 09:02 PM
|
Replies: 9
Views: 5,211
die polishing
I agree with what I have read here ,but I go alittle farther and use a dremel tool with a buffing pad in it, with red rough on it, and sometimes I use Flitz.
I the buffing pad is to big, I use some...
|
Forum: Small Caliber Discussion Board
01-24-2007, 01:54 PM
|
Replies: 10
Views: 4,759
|