Forum: Bullet Making
09-24-2014, 04:23 PM
|
Replies: 26
Views: 15,309
thanks for all the info
Hi Lads
A big thanks for all the info and i don't think ill be getting in jacketed bullet making just yet , I managed to find a few box's of 30gr bergers that i have been using,
luke
|
Forum: Small Caliber Discussion Board
09-24-2014, 04:19 PM
|
Replies: 11
Views: 4,617
it could be done
hi
you will need to open up bolt face and it can be cut with a small carbide boring bar.
luke
|
Forum: Bullet Making
09-12-2014, 07:58 PM
|
Replies: 26
Views: 15,309
set up cost
Hi George
Could you please advise me on what would be needed if I was to start making my own bullets in .17 cal
thanks luke
|
Forum: Bullet Making
09-12-2014, 03:47 PM
|
Replies: 26
Views: 15,309
Hot core ?
hi George Ulrich
thanks for the info can see the spring back in jacket and core differ, as lead as a lot lower melting point than gilding metals annealing point , but it all sounding like a lot of...
|
Forum: Bullet Making
09-11-2014, 08:50 PM
|
Replies: 26
Views: 15,309
thanks again
hi Lads
well i think this weekend ill have a go at making myself a draw die set , i have nothing to loss but bit of time,
.204 less .172 is .032 so i figger ill try on one go and see if it...
|
Forum: Bullet Making
09-08-2014, 06:52 AM
|
Replies: 26
Views: 15,309
Thanks for the info
Hi Lad's
thanks for the info . Going to have get a draw die then .
Thanks luke
|
Forum: Bullet Making
09-07-2014, 02:15 PM
|
Replies: 26
Views: 15,309
.20 cal to 17 cal will it work ?
hi
i am think of sizing .20 cal to .17 cal
as i can no longer get any 30gr .17 here in uk
as any one tried this and what do i need ?
thanks
luke
|
Forum: Small Caliber Discussion Board
04-27-2014, 06:34 PM
|
Replies: 18
Views: 6,422
mag bodys
hi.
just mill it out to fit , you need the re-cut the ramp too. but that easy to, jut don't cut any off the abutment height,
hope this makes it easier,
my .17fb is on 222 action ,
222,...
|
Forum: Project Guns
04-07-2012, 10:02 PM
|
Replies: 8
Views: 22,689
that springy plate
i work o a few of this and have found a dab of super glue to hold it to the action dose no harm:)
|
Forum: Small Caliber Discussion Board
12-15-2011, 08:45 PM
|
Replies: 67
Views: 23,299
brass
i hope they get there act together on brass , the only bag i got was that bad i have been making my owen form .223 a real mess around
|
Forum: Small Caliber Load Data
11-24-2011, 08:46 PM
|
Replies: 5
Views: 3,851
not goning to try it
hi lads
i use lil gun in my 22hornet 10.3 gr and 45 gr hornady bee bullets
so i have the powder a round and saw the same question on a from in here in enland so i throught id ask it here as
we...
|
Forum: Small Caliber Load Data
11-21-2011, 10:41 PM
|
Replies: 5
Views: 3,851
thanks lads
hi all
thanks for that ,its just as throught ,
:(
|
Forum: Small Caliber Load Data
11-20-2011, 08:08 PM
|
Replies: 5
Views: 3,851
lil gun in .17 fb or mach4
hi
i have seen the question asked on a uk from,
i think lil gun would be to fast to get the best out of .17 fb.
i would like to hear if any one as tried it? and what resultes they got ?
thanks...
|
Forum: Small Caliber Load Data
10-31-2011, 07:43 PM
|
Replies: 23
Views: 11,104
|
Forum: Small Caliber Load Data
10-30-2011, 10:40 PM
|
Replies: 23
Views: 11,104
|
Forum: Small Caliber Load Data
10-30-2011, 10:30 PM
|
Replies: 23
Views: 11,104
|
Forum: Small Caliber Load Data
10-26-2011, 06:01 PM
|
Replies: 23
Views: 11,104
|
Forum: Small Caliber Load Data
10-25-2011, 09:55 PM
|
Replies: 23
Views: 11,104
made frist case today
hi finished making my die ,
i have bored out a lee full lenght .221 die to take bushings
,i had set should back with it as standerd but this made creases in shoulder
so bore it out and have made...
|
Forum: Small Caliber Load Data
10-19-2011, 08:45 PM
|
Replies: 17
Views: 8,697
h322
i have only just started playing with my 17fb , but had some h322 from when i had 223 , and i have found that 17.5gr is working well with the 30gr bergers
going to tring 25 vmax soon as i make...
|
Forum: Small Caliber Load Data
10-16-2011, 06:45 PM
|
Replies: 23
Views: 11,104
just getting all the bit together , looking...
just getting all the bit together , looking forward to doing it as th brass i can gat is not any good found 2 case with spilt neck's 1 with undersize rim and 8 with poorly formed shoulders
and...
|
Forum: Small Caliber Load Data
09-26-2011, 09:37 PM
|
Replies: 23
Views: 11,104
|
Forum: Small Caliber Load Data
09-25-2011, 08:48 PM
|
Replies: 23
Views: 11,104
|
Forum: Small Caliber Load Data
09-25-2011, 07:57 PM
|
Replies: 23
Views: 11,104
.17 fire ball case from .223
hi
iam going to make my owen case's
how meny forming die do i need to make ,
i was thinkin ill need to go to 7mm then 6.5 them 6 mm the a .221 fire ball die
the neck to .20 cal then full...
|
Forum: Project Guns
08-20-2011, 02:57 PM
|
Replies: 3
Views: 4,441
rota mod
if you are going to rimmless case you could just remove all but the first vain,on the rota, some steyr mag work like this, the older .222 /.223
|
Forum: Small Caliber Load Data
08-04-2011, 10:40 PM
|
Replies: 14
Views: 7,094
|