Forum: Small Caliber Discussion Board
11-12-2019, 03:33 AM
|
Replies: 10
Views: 4,662
Teslong Borescope
Following 358SCOTT's clue, I found that the top of the mirror does indeed stick out over the edge of the tube. I measured it at about 0.203". Most of the rest of the assembly measured around...
|
Forum: Small Caliber Discussion Board
11-07-2019, 03:20 AM
|
Replies: 10
Views: 4,662
Teslong Borescope
I have one of these too. I found that it would fit my friend's .204, but will not fit either of my 5mm Rem. Mags. I'll try your fix.
I've had the Lyman bore scope for several years and all of...
|
Forum: Small Caliber Discussion Board
07-30-2017, 08:00 PM
|
Replies: 11
Views: 6,370
Canjar for 788
I have one 788 with a Canjar trigger. I just pulled the receipt out and it is a Model 788-2/2 Deluxe Trigger and cost $27.20 on April 7, 1975. I've had it set for a 12 oz. pull for many years and...
|
Forum: Small Caliber Discussion Board
06-28-2017, 02:43 AM
|
Replies: 2
Views: 2,566
580
How did your gunsmith deal with the extractors? I had to remove a lot of material from mine to handle the wider, thicker rim and I kind of worried about it. I've fired around 300 rds. with no...
|
Forum: Small Caliber Discussion Board
03-25-2017, 10:22 PM
|
Replies: 73
Views: 24,476
580 conversion
I rechambered a 580 that I had made up as a .17 HMR to .17 WSM. You have to open up the extractors to take the larger rim and I put in a "Wolff" firing pin spring to get a little harder hit on the...
|
Forum: Small Caliber Discussion Board
03-15-2017, 04:24 AM
|
Replies: 16
Views: 5,989
Hornady H.P.
I used these and also the Remington HPPL on coyotes and they both shot well and never exited. I never recovered a bullet in one piece as shown. Only tiny jacket and lead fragments. In my...
|
Forum: Small Caliber Discussion Board
03-05-2017, 05:56 AM
|
Replies: 10
Views: 4,592
Rifle primers in a handgun
It shouldn't be dangerous but they probably won't fire on the first try since the rifle primers have a "thicker" cup than pistol primers. You may wind up having to pull the bullets and start over if...
|
Forum: Small Caliber Discussion Board
08-28-2016, 02:20 AM
|
Replies: 17
Views: 7,170
I bought the "200" pack of the new A-22 in a...
I bought the "200" pack of the new A-22 in a Ranch Supply store for $59.95. Widner's should stick to selling powder and brass. A lot of this overpricing "stuff" going on is not "supply and demand",...
|
Forum: Small Caliber Discussion Board
02-06-2016, 02:02 AM
|
Replies: 11
Views: 6,982
|
Forum: Small Caliber Discussion Board
09-01-2015, 03:23 AM
|
Replies: 11
Views: 5,658
|
Forum: Small Caliber Discussion Board
04-25-2015, 08:00 PM
|
Replies: 10
Views: 4,982
|
Forum: Small Caliber Discussion Board
04-25-2015, 07:58 PM
|
Replies: 9
Views: 4,308
|
Forum: Small Caliber Discussion Board
04-04-2015, 06:34 AM
|
Replies: 6
Views: 3,219
|
Forum: Small Caliber Discussion Board
02-22-2015, 08:04 PM
|
Replies: 10
Views: 4,858
|
Forum: Small Caliber Discussion Board
01-30-2015, 01:36 AM
|
Replies: 18
Views: 8,178
|
Forum: Small Caliber Discussion Board
01-19-2015, 04:37 AM
|
Replies: 14
Views: 5,482
|
Forum: Small Caliber Discussion Board
01-13-2015, 12:31 AM
|
Replies: 40
Views: 19,012
|
Forum: Small Caliber Discussion Board
12-21-2014, 04:07 AM
|
Replies: 20
Views: 11,712
Eric,
I'm sure I read somewhere that the...
Eric,
I'm sure I read somewhere that the 5mm Rem. Mag. operated at 38,000 psi and not 33,000. I can't lay my hands on the information right now. Perhaps that was the "proof" load.
Bob
|
Forum: Small Caliber Discussion Board
12-07-2014, 06:05 AM
|
Replies: 19
Views: 8,281
O.K. I did not know that. Just goes to make my...
O.K. I did not know that. Just goes to make my point even more. I have some old 2015 powder that was made in China and some that was made in Israel or at least that's what it says on the label. I...
|
Forum: Small Caliber Discussion Board
12-05-2014, 09:13 PM
|
Replies: 19
Views: 8,281
Powder Re-branding
I've been wondering for the past few years just how many of the powders we're buying are almost like, or identical to the ones we have been using. Different "lot numbers" of the same powder with a...
|
Forum: Small Caliber Discussion Board
12-03-2014, 06:17 PM
|
Replies: 19
Views: 8,281
New Powders
It appears that the main difference is that the new powders have the "Copper Fouling Eliminator" component added. Like CFE223 has.
Bob
|
Forum: Small Caliber Discussion Board
11-23-2014, 09:08 PM
|
Replies: 9
Views: 4,101
|
Forum: Small Caliber Discussion Board
10-28-2014, 02:34 AM
|
Replies: 6
Views: 2,900
|
Forum: Small Caliber Discussion Board
10-07-2014, 03:28 AM
|
Replies: 44
Views: 18,385
New Member
Welcome Christoffer. That was really a bad crown. It appears to have been done with a dull countersink bit. Your Smith did a good job. I'm puzzled as to what the exchange rate it between your...
|
Forum: Small Caliber Discussion Board
10-02-2014, 05:32 AM
|
Replies: 7
Views: 15,288
Searches
I agree that it must be your Internet Service Provider. I've not had any problem with Google on any "gun searches".
Bob
|