#1
|
|||
|
|||
17 tcm/17 9mm
did a sarch on the forum and nothing , why hasn't someone necked it down to 17, has to exceed the 17 vha velocities by a wide margin.
i have been away too long.
__________________
I post here because it keeps the riffraff away. 'Life's Journey is not to arrive at the grave safely in a well preserved body, but rather to skid in sideways, totally worn out, shouting, Holy sh!t... What a Ride! |
#2
|
|||
|
|||
I picked up some 22 TCM brass. Got it necked down to 17 but no barrel chambered yet. My plan is to run a 17 Fireball reamer in "short" and load the round. 6 to 8 grains of powder should get the job done.
The 17 VHA is in the works also. As far as how fast it will go, won't know till I get it to go BANG! |
#3
|
|||
|
|||
how is the case capacity compared to the vha.
__________________
I post here because it keeps the riffraff away. 'Life's Journey is not to arrive at the grave safely in a well preserved body, but rather to skid in sideways, totally worn out, shouting, Holy sh!t... What a Ride! |
#4
|
|||
|
|||
I think the FB reamer is a little tight at the shoulder, I made a sizing die for a TCM to 20 Cal. by running my 17 FB reamer in short in a blank die, then reaming the neck to size it to 20. Larry
__________________
A gun is just like a parachute, if you really need one, nothing else will do. |
#5
|
|||
|
|||
QL lists the 22TCM at 16.8grains of H2O and the 4.6x30 at 14.4
So the 17TCM should be in 17HH territory. |
#6
|
|||
|
|||
Search ray h and 17-20 boomer. It's been done. And the 22 TCM has nothing to do with 9 mm. Not even close. It's longer. It's based off the 223 case.
|
#7
|
|||
|
|||
What I did was neck down the 22 TCM case to 17, then ran it up into a 17 Fireball die to make sure the shoulder hadn't spread out.
Next step will be to run a 17 caliber mandrel in the neck then the case into a "shortened" 17 Fireball die. If I form with the Fireball die, it should match the reamer. One step at a time. |
#8
|
|||
|
|||
pictures??????????????????????????????
__________________
I post here because it keeps the riffraff away. 'Life's Journey is not to arrive at the grave safely in a well preserved body, but rather to skid in sideways, totally worn out, shouting, Holy sh!t... What a Ride! |
#9
|
|||
|
|||
just going by this article http://www.gunblast.com/RockIsland-22TCM.htmi realize the 9mm is based off the .223
__________________
I post here because it keeps the riffraff away. 'Life's Journey is not to arrive at the grave safely in a well preserved body, but rather to skid in sideways, totally worn out, shouting, Holy sh!t... What a Ride! |
#10
|
|||
|
|||
The availability of TCM brass has me all giddy inside. Don K. sent me a Boomer case and all I can say is that I am happy I didn't build the Shrew a few years back. A 22TCM case necked down to 17 caliber with a 40 degree neck appears to be as close to perfection as one can get. I can't wait!! I look forward to hearing everyone's progress reports on their projects as they go forward.
__________________
Waska Last edited by Waskawood; 10-04-2014 at 03:02 PM. |
Thread Tools | |
Display Modes | |
|
|