Saubier.com  



Go Back   Saubier.com > Saubier.com Forums > Small Caliber Discussion Board

Reply
 
Thread Tools Display Modes
  #1  
Old 02-03-2012, 09:29 PM
Remmynut Remmynut is offline
Senior Member
 
Join Date: Jul 2008
Location: Northern Indiana
Posts: 226
Default CZ clip assembly.....(and first groups).

Is there a link showing the assembly of the parts holding a CZ 527 clip in and how to install them reassembling a 527?

No instructions with a used rifle and parts falling out when disembling do NOT lend themselves well to reinstalling them.

Holy PIA Batman!

Thanks in advance.

Steve

Last edited by Remmynut; 02-04-2012 at 02:39 AM.
Reply With Quote
  #2  
Old 02-03-2012, 09:55 PM
ab_bentley ab_bentley is online now
Supporting Member
 
Join Date: Sep 2008
Location: Dresden, Ohio 43821
Posts: 5,977
Send a message via MSN to ab_bentley
Default

Put them back together in this order:

Follower
Spring
Wedge
Floorplate
__________________
-Dresden Gun Company, Ltd-
-Dresden, Ohio-
- Creating Beauty Through Craftsmanship of Wood & Metal-







Reply With Quote
  #3  
Old 02-03-2012, 10:24 PM
RePete RePete is offline
Senior Member
 
Join Date: May 2007
Location: Idaho, Clearwater County
Posts: 1,479
Default

CZ has a PDF you can download on their web-site.
Shows a nice detail of the mag and it's parts.

http://www.cz-usa.com/assets/product...s/CZ_527US.pdf

Luck
Charlie
__________________
I plead the 2nd.
Reply With Quote
  #4  
Old 02-04-2012, 02:30 AM
Remmynut Remmynut is offline
Senior Member
 
Join Date: Jul 2008
Location: Northern Indiana
Posts: 226
Default Thanks, Guys

I KNOW it will get easier.........about the 14 th time.

Appreciate the help.

Zeroed scope today (cheapie one ) and took a few "work up" loads to the range.

A. 52 gr HP hornadys dont shoot worth snot in this 1-16 twist. (POI was 8-9 inches off from the 50 grain SXSP and LARGE groups)

B. 50 gr SXSP shot "ok". I didn't expect wonders from hunting bullets and virgin brass. Waiting on some 45 grainers.

C. Highest loads taken were 12.6 grains of LGun and shot the best with zero pressure issues visible.

So...just a start but "good enough to kill a coyote" for now but work in progress.

MIGHT have done a little better had the buddy I went with went first. I noticed a definate PROBLEM with front pad on the rest for the forearm as in it MOVED very easily but since this guy is a friend and didnt want to appear ungrateful of his help, I didnt say anything and shot the best I could, stuggling to hold the ding dang X hairs still on the target.

When I was done and out ammo he sat down, sat his 700 17 Rem down on the rest and said "What the heck is wrong with this front pad?" and promptly screwed the front pad down on the spindle complaining about his grandson "messing with his stuff". ( I checked it later.......like a rock. )

So...anyway.

Old, half blind, in a bit of a rush, virgin brass, only a few bullet selections and a few loads, a wiggly rest, new to the gun and trigger and not being much of a "bench guy" (cant think of any other "excuses" lol)......I cant complain.

50 grain SXSP
12.6 grains Lil Gun
WW Small Pistol primers
WW New brass
approx 10mph x wind

200 yards.




Second group, same combo, I shot five shots and realized quickly (aka at 4-5 shot) that cooling the barrel for max groups would be mandatory (and normal IMHO). Same results for the first 3 but shots 4-5 were 2 inches out. (coulda been yours truly too)



A start. Had fun and after a couple clicks of fine adjustment I'm "huntable" at least. Hope that some other bullets, neck sizing, crimping and load tweaking shows improvement.

I was a little surprised at the few that came around asking about( "a WHAT?" ) 22 hornet.

Just info.

God Bless
Steve
Reply With Quote
  #5  
Old 02-04-2012, 06:32 PM
Mike Casselton Mike Casselton is offline
Senior Member
 
Join Date: Dec 2006
Location: Valrico FL
Posts: 359
Default

One thing I have found with the CZ 527 is that when shooting groups, you need to hold the rifle tightly to your shoulder for best accuracy. I also get better groups without the set trigger
Reply With Quote
  #6  
Old 02-04-2012, 07:25 PM
sicero sicero is offline
Supporting Member
 
Join Date: Sep 2006
Location: Medway, Ohio
Posts: 2,491
Default

As Mike says, the CZ trigger can be adjusted to a veryvery nice trigger without the set. Kenny
__________________
sicero

I pride myself in being able to make decisions with little information.
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT. The time now is 10:04 PM.


Powered by vBulletin® Version 3.8.1
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.